Chevy Camaro Chevrolet

90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet

90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet

90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet    90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet
90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevroletd. 90 Degree Univesal Lambo Door Hinge Kit. Bolt On Vertical Door Kit For Chevrolet. Vertical door hinge kit, bolt on installation for universal usage. Vertical doors overturn traditional outward opening way with upward opening hinges.

As hinge positions are the same as ordinary cars, almost all vehicles are qualified to be refitted into vertical doors, including open cars. By applying vertical door hinges, door opening can be done even in narrow areas, thus avoiding possible damages to pedestrians and doors themselves. Brand new vertical door hinge kit with good quality. Two 90 degree structures included. Four gas charged struts of 150 PSI.

Bolting, drilling and welding may be required. Fenders on some vehicles may need to be rolled. Installation should be accomplished by professional mechanics. Universal fitment for most cars. Compatibility: Universal fitment for most cars.

Gross Weight: 37 lbs (16.8 kg). Package Dimensions (L W H): 22.4"17" 5 (57 43 13 cm).

This product requires welding and screw fixation, which should be accomplished by a professional mechanic. Fenders may need to be rolled for some vehicle models.

If your door is equipped with power locks or windows, you may or may not need to extend the wires going from the door to the chassis depending on how much slack there is. You might need a wire extension kit. Will not damage original car structure. Easy to teardown and recover to original way of opening. Universal usage, compatible with most cars including Chevrolet, Nissan, Mazda, Ford, Subaru, Toyota, etc.. 1 x Vertical Doors Hinge Kit. Remove door panels and lower dash panels for easier access. Remove fenders, and all necessary parts to remove them. Remove door stop bar if applicable.

Remove all wiring running in to the door. Close door and remove upper hinge. Test fit Protocol Upright Door Hinge for correct placement on vehicle. Be sure that the location the hinge will mount is flat, remove any unneccassary flanges or mounts.

NOTE: if cutting must be done be sure the chassis structure remains in fact. Hold the hinge in place and tack weld it in position, on chassis and door.

Be sure all measurements are correct before welding, or you may need to cut the welds and start over. Open door and test the swinging motion. NOTE: use caution as there is nothing holding the door up.

Close door and replace fender to test the fit and motion. Open door slowly, mark locations on fender that will need to be rolled or cut away, fender flange may need to be removed for more clearance.

Mark location on safety limit bar (on upright Door hinge) for correct outward movement. Extend all wiring running into the door, to allow for vertical travel, (solder all connections to prevent electrical problems) open and raise to measure for wire length. Remove wires from the loom and cut. Cut on wire at a time to prevent mistakes. Solder the appropriate extension lead and tape/heatshrink.

A longer wire loom may be needed. Make all the proper adjustments, to allow for smooth opening and closing operation. See Fine Tuning section below. With door open, attach strut to the hinge, locate and mark mounting position for ball stud on chassis.

Attach ball stud to chassis using either the supplied mount or fabricate one for your specific application. Re-attach fender and all parts, that were removed and test motion. Unpaid item (UPI) complaint will be filed against non-paying buyers after 4 days. Above time are for reference ONLY. We DO NOT guarantee the arrival time. (Usually we'll lower the value and mark the item as gift). We accept 30 days return only if item is original. The item "90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet" is in sale since Wednesday, August 8, 2018.

This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Exterior\Other". The seller is "jdm_car" and is located in Walton, Kentucky.

This item can be shipped to United States.

  • Country/Region of Manufacture: China
  • Color: Metallic Silver
  • Manufacturer Part Number: KD6050
  • Brand: Kyostar Motors
  • Warranty: 1 Year


90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet    90 Degree Univesal Lambo Door Hinge Kit Bolt On Vertical Door Kit For Chevrolet